Latest activity

What's new New posts Latest activity

D

DanOnTheBoat reacted to kd4pbs's post in the thread Mercruiser Setting Timing on 3.0L with Like.

Very good - it appears they don't go into the water jacket, so you won't need sealant on the threads. Fel-Pro's marine sets are decent...

4 minutes ago
M

muc replied to the thread WOT RPM Low. MAG350 MPI B3.

First I would check that the fuel pressure gauge is accurate. Might be relevant why the heads and injectors were replaced. In‑Water...

15 minutes ago
Fun Times reacted to muc's post in the thread B3X upper gearset lash with Like.

Assuming you have all the tools and are following the service manual. That you have the exact same out of spec backlash on both gears is...

25 minutes ago
Fun Times reacted to muc's post in the thread B3X upper gearset lash with Sad.

Merc quit stamping numbers in the upper awhile back. Hope O.P. isn't in #28, that manual was like 600 pages in it's last version...

26 minutes ago
N

ntanner replied to the thread 1970s Starcraft SS 160 refinish.

14 14 holes total, one hole underneath each side of 7 of the ribs.

34 minutes ago
C

cmon74 replied to the thread 2018 suntracker 16 with 40hp Bigfoot Mercury.

Right. It would be nice to know but it is what it is. Runs perfect so no issues there. I just find it odd is all

34 minutes ago
A

acadian2022 replied to the thread 1980's serial number / harness / general questions.

good day. anyone know what are the specs for the power head bolts serial number for the block is 6033659 and the head number is 95081. I...

Today at 11:57 AM
M

muc replied to the thread B3X upper gearset lash.

Merc quit stamping numbers in the upper awhile back. Hope O.P. isn't in #28, that manual was like 600 pages in it's last version...

Today at 11:43 AM
C

Chris1956 replied to the thread Modern PT lumber.

The pilings that Venice is built on were whatever was available in Europe at the time. They were a mix of soft and hard wood. They...

Today at 11:39 AM
T

tphoyt replied to the thread Modern PT lumber.

I love seeing the beautiful woods that are reclaimed from rivers and lakes that have been there for 100 or more years. A lady I used to...

Today at 11:10 AM
redneck joe replied to the thread 1970s Starcraft SS 160 refinish.

How many holes

Today at 10:54 AM
redneck joe reacted to acadian2022's post in the thread power trim removal of center cylinder with Like.

Quick update nothing Ive done worked. I was able to tap a new hole in the ram and got the power trim system to work for now this will do...

Today at 10:53 AM
Grub54891 replied to the thread 1981 MerCruiser 120 tick/ squeak.

Your riser/ manifold should not get that hot. Service the impeller, look for any clogs in the input from the pump. The tock may be the...

Today at 10:53 AM
Grub54891 replied to the thread Testing my temp gauge.

You can test it in a pot of hot water without running the motor. Be sure to hook up a go ground and keep the connector on the top.

Today at 10:47 AM
Scott Danforth replied to the thread Testing my temp gauge.

first, check the ends of the wire at teh gauge and sender (tan wire) check the ground at the gauge most likely its corrosion on the...

Today at 10:34 AM

Show older items

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Latest activity

Follow Us